EXPERIMENTAL STUDY OF CARBON MEDIA VARIATIONS SEM TEST AND TEMPERATURE ON STAINLESS STEEL 316L PACK CARBURIZING COATING ON THERMAL CONDUCTIVITY AND CORROSION RATE

Reinardi Odilian Jahu; Nereus Tugur Redationo; Bernardus Crisanto Putra Mbulu

doi:10.59581/metal.v4i1.148

EXPERIMENTAL STUDY OF CARBON MEDIA VARIATIONS SEM TEST AND TEMPERATURE ON STAINLESS STEEL 316L PACK CARBURIZING COATING ON THERMAL CONDUCTIVITY AND CORROSION RATE

Authors

Reinardi Odilian Jahu Universitas Katolik Widya Karya
Nereus Tugur Redationo Universitas Katolik Widya Karya
Bernardus Crisanto Putra Mbulu Universitas Katolik Widya Karya

DOI:

https://doi.org/10.59581/metal.v4i1.148

Keywords:

Coconut Shell, Arabica Coffee Grounds, Thermal Conductivity, Carbon Content, Pack Carburizing, Stainless Steel 316L, Corrosion Rate and Temperature

Abstract

This study analyzed the characteristics of carbon produced from coconut shells and Arabica coffee grounds through a pyrolysis process at a temperature of 1000°C for 1 hour. The SEM test results showed that coconut shells contained 91.87% carbon, while Arabica coffee grounds contained 74.39% carbon, indicating a higher carbon content in coconut shells. Furthermore, this study evaluated the effect of coconut shell carbon and Arabica coffee grounds carbon with temperature variations on the thermal conductivity and corrosion rate of 316L stainless steel plates. The results of the study showed that the highest thermal conductivity values for coconut shell carbon and Arabica coffee grounds were 19.06087 W/m°C and 18.959905 W/m°C, respectively, both achieved at a temperature of 900°C. Increasing the temperature in the pack carburizing process significantly increased the carbon content in 316L stainless steel, which had a positive impact on increasing thermal conductivity. Coconut shell carbon at 900°C showed the lowest corrosion rate of 4.35 mm/year, while Arabica coffee grounds carbon at the same temperature had a corrosion rate of 5.81 mm/year. In conclusion, the effect of adding carbon with temperature variations in the pack carburizing process can increase hardness. The corrosion rate on 316L stainless steel plate will be lower because it contains Cr, Ni, and C which affect strength and high temperature resistance, especially hardness.

References

[1] A. F. Abidah, “Analisa SS400 Hasil Carburizing Media Arang Tempurung Kelapa-BaCO3 Dengan Variasi Temperatur Pemanasan Dan Holding Time Ditinjau Dari Pengujian Kekerasan Dan Struktur Mikro,” Jtm, vol. 07, no. 02, pp. 1–8, 2019.

[2] Surya. Studi, T. Mesin, F. Teknik, U. Katolik, and W. Karya, Pemanfaatan karbon tempurung kelapa dan cangkang sawit sebagai bahan pack carburizing untuk meningkatkan kekerasan dan mengurangi laju korosi stainless steel tipe 304. 2024.

[3] A, Lody. Analisis perbandingan campuran komposisi karbon, semen dan air terhadap laju konduktivitas panas, kapasitas kalor dan efisiensi kapasitas kalor (Doctoral dissertation) (2019).

[4] R. Idrus, B. P. Lapanporo, and Y. S. Putr, “PRISMA FISIKA , Vol . I , No . 1 ( 2013 ), Hal . 50 - 55 ISSN : 2337-8204,” vol. I, no. 1, pp. 50–55, 2013.

[5] A. J. Sinaga and C. Manurung, “Analisa Laju Korosi dan Kekerasan Pada Stainless Steel 316 L Dalam Larutan 10 % NaCl Dengan Variasi Waktu Perendaman,” Sprocket J. Mech. Eng., vol. 1, no. 2, pp. 92–99, 2020, doi: 10.36655/sprocket.v1i2.186.

[6] D. Shilsilia, I. Khaldun, and A. Aktif, “Efektivitas Penggunaan Arang Aktif Dari Ampas Bubuk Kopi Arabika (Arabica Gayo Coffee) Sebagai Adsorben Ion Fe2+,” J. Ilm. Mhs. Jur. Pendidik. Kim., vol. 8, no. 2, pp. 66–74, 2024.

[7] T. Metalurgi, U. Sultan, A. Tirtayasa, and A. Naznabila, “Efek quenching dan partitioning terhadap sifat mekanik, ketahanan korosi, dan struktur mikro pada stainless steel 316l,” 2025.

[8] R. L. Kevin J. Pattireuw, Fentje A. Rauf, “Analisis Laju Korosi Pada Baja Karbon Dengan Menggunakan Air Laut Dan H2So4,” Univ. Sam Ratulangi Manad., p. 10, 2013.

[9] D. Fernianti, “Analisis Kemampuan Adsorpsi Karbon Aktif Dari Ampas Kopi Bubuk Yang Sudah Diseduh,” Berk. Tek., vol. 3, no. 2, pp. 563–572, 2013, [Online]. Available: https://jurnal.um-palembang.ac.id/berkalateknik/article/view/361

[10] I. Hafizi, W. Widjijono, M. Heparis, and N. Ekandaru, “Penentuan Konsentrasi Stainless Steel 316L Dan Kobalt Kromium Remanium GM-800 Pada Uji GPMT Untuk F ksasi Tulang . Mulai Dari Hal Sederhana Steel Karena Adanya Potensi Korosi Pit Ataupun,” Kedokt. Gigi Indones., vol. 2, no. 3, pp. 121–127, 2016.

[11] I. K. Suarsana, I. M. Astika, and I. G. P. Agus Suryawan, “Efek perlakuan pack carburizing dan media korosif pada baja AISI 1045 terhadap laju korosi,” J. Energi Dan Manufaktur, vol. 14, no. 2, p. 37, 2022, doi: 10.24843/jem.2021.v14.i02.p01.

[12] R. J. Fajri, “Pemanfaatan Limbah Kulit Kopi Arabika (Coffea Arabica) Menjadi Karbon Aktif Sebagai Adsorben Zat Warna Metilen Biru,” Skripsi, pp. 1–76, 2023.

[13] G. Sania, “PEMANFAATAN KARBON AKTIF DARI AMPAS BIJI KOPI (Robusta),” 2021.

[14] N. T. Redationo, “Karakterisasi Serbuk Tempurung Kelapa Sebagai Bahan Target Dengan Variasi Temperatur Pemanasan,” Wawasan, vol. XXVI, no. 1, pp. 27–34, 2017, [Online]. Available: http://lppm.widyakarya.ac.id/wawasan-volume-xxvi-1-nereus-tugur-redationo/

[15] V. D. Pratiwi and I. Mukhaimin, “Pengaruh Suhu dan Jenis Perekat Terhadap Kualitas Biobriket dari Ampas Kopi dengan Metode Torefaksi,” CHEESA Chem. Eng. Res. Artic., vol. 4, no. 1, p. 39, 2021, doi: 10.25273/cheesa.v4i1.7697.39-50.

[16] B. C. P. Mbulu, N. T. Redationo, and F. V. Herwinsha, “Calculation Analysis Of Heat Conductivity And Average Heat Rate In Carbon Composites,” J. Met., vol. 1, no. 2, pp. 17–24, 2023.

Downloads

Published

2026-06-30

How to Cite

Odilian Jahu, R., Tugur Redationo, N., & Crisanto Putra Mbulu, B. (2026). EXPERIMENTAL STUDY OF CARBON MEDIA VARIATIONS SEM TEST AND TEMPERATURE ON STAINLESS STEEL 316L PACK CARBURIZING COATING ON THERMAL CONDUCTIVITY AND CORROSION RATE. Mechanical, Energy and Material (METAL), 4(1), 1–11. https://doi.org/10.59581/metal.v4i1.148